Introduction

The Renault AG1 car was produced from 1905 through to 1921 and while I cannot find information on how many were built I do know that there where many different variants. It is my understanding that the engine cowling was a common feature of all the variants and so I suspect that ICM has more versions of this vehicle in the wings if demand is there. This vehicle had a two cylinder engine with a top speed of around 25 MPH.

The Renault AG1 car appears to have been the vehicle of choice when it came to taxis in France and specifically Paris and it is this aspect that this release from ICM represents. On September 6th 1914 approximately 1,500 taxis assembled and transported between 5,000 and 7,000 French troops (depending on who you believe) to the front to face the Germans and halt their advance. My research suggests that 5 soldiers and the driver were supposed to be the numbers riding each taxi and that meant standing on the running boards. This action resulted in the Renault AG1 taxi obtaining the title of ‘Taxi de la Marne’. ICM has taken the 1/35th scale offering and up scaled it to 1/24th scale.

Review

This offering from ICM is packaged in the usual way of a flip top cardboard tray and an additional card lid with all of the artwork on it; this approach means that the model has a very good chance of reaching you in the condition it was meant to regardless of how it is sent. Inside of the box you will find a single re-sealable plastic bag containing the parts for the taxi and also two other bags with the tyres and the clear parts. There is a decal sheet tucked inside the instruction booklet.

This version of the Renault AG1 is a four seater, two in the spacious enclosed rear cab and two on the front seat one of whom would of course be the driver. This vehicle is a soft topped version of the Renault AG1 and from checks against online images of preserved examples and period photographs it looks to have been well replicated in this release from ICM in 1/35th scale. The area of the roof between the doors is rigid rather than cloth.

This offering from ICM has a chassis made of 4 main parts that are assembled at the start of the instructions that is then cemented to the running boards and mudguards. I suggest that this be considered a single step as it will help to ensure that the chassis is square. The mudguards have nice raised detail that will help when adding the pin line detailing during the painting process. The chassis being moulded in parts has allowed a nice level of detail to be added and pleasingly the parts would seem to be free of ejector pin marks. The same cannot be said of the running boards and mudguards where there are some very deep ejector pin marks on the underside that will need to be tackled.

ICM has as usual tackled the engine of the Renault and while I was unable to find pictorial reference it does look nice. Due to the fact that this is a 2 cylinder engine I have to believe it is an accurate representation of the engine. Unfortunately it does not appear that the engine and other detail provided here will easily be seen or displayed on the finished model. If you do wish to do the work needed to display this aspect of the model then some wire and a little work should provide a little gem. ICM has also provided the radiator which is behind rather than in front of the engine with the relevant plumbing also provided. The transmission is another nicely provided detail that with the exhaust creates a very nice level of detail as regards the mechanical aspects of the model. I believe the engine cowling could be raised from the front and hinged at the rear and then held in place by a rod; I have found an image to support that belief and then others show the hood split.

The front leaf springs are moulded as part of the chassis that with a little work to clean the mould seams will look good. The rear leaf springs are moulded separately and again a little work on the mould seams will raise the level of the finish. The steering mechanism is locked in a forward position only and that is an aspect I don’t like as I always feel that with the wheels turned a model looks more visually pleasing. The wheels have wooden spokes provided that would not look at of place on a horse coach, these are then finished with tyres provided in vinyl by ICM. The rear axle and differential looks good which due to being easily seen is a good aspect of the model.

The body work of the model has been tackled well and while in several parts care will result in a pleasing finish I believe. The inner surfaces do seem to have a number of ejector pin marks that will need to be tackled and while they don’t all need filling best practice says otherwise. The doors of the rear cab could be left open if desired with the interior detail being of a standard to allow that without much in the way of work. The soft roof panels have been well tackled with a good level of detail representing the metal frame work of the support structures. The lights have been well tackled that with some work I believe it would be possible to add LED’s to them, but my research indicates that tail lights only were used during the event of getting the French Army to the front.

The model is shown finished in a red livery which is supported by photographs; I have also found images of the vehicle finished in a green livery should you so decide. ICM has provided decals for the model including 3 alternate sets of registration plates. There are three other decals provided on the sheet but I am at a loss as to what they represent.

Conclusion

This offering from ICM is as far as I can see a direct enlargement of the earlier model released in 1/35th scale, and while this may offend some I do not have an issue with it. The quality of the model holds up in this scale and will I believe meet with approval of the modellers who prefer the larger scale. The result should be a very pleasing and stunning model in the red livery.